powerlase
technical papers
POWERLASE engineers are at the forefront of their field. The publicly available papers are listed below.
"A Novel Laser Technique for Patterning Black Matrix in LCD Manufacture"
Presented at ICALEO Orlando '07, Florida - October 2007
"Rapid Laser Patterning versus Wet-Etch Lithography for FPD Manufacture: A Technical & Commercial Comparison"
Presented at ICALEO Orlando '07, Florida - October 2007
"Innovative Applications in FPD Manufacture using High Power Q-Switch DPSS Lasers "
Presented at CLEO Pacific Rim '07, Seoul, Korea - August 2007
"Rapid Laser Patterning of ITO on Glass for Next Generation Plasma Display Panel Manufacture"
Presented at Society for Information Displays SID'07, Long Beach, California, USA - May 2007
"Laser Direct Write of Active Thin Films on Glass for Industrial Flat Panel Display Manufacture"
Published by the Japan Laser Processing Society (JLPS) in the fourth issue Vol. 2, No. 1 of the Online Journal (http://www.jlps.gr.jp/jlmn/) - March 2007
http://www.jlps.gr.jp/jlmn/06-041.pdf
"Nano Scale Analysis of Laser Ablated Thin Films used in Industrial Manufacturing of Flat Panel Displays"
Presented at ICALEO - October 2006
"Laser Engraving Reflective Metals to Create Scanner Readable Barcodes"
Presented at ICALEO - October 2006
"Laser Engraving Scanner Readable Barcodes on Automotive Materials for Traceability and Security Applications"
Presented at ALAC, Michigan, USA - September 2006
"Laser Ablation of ITO Thin Films on Glass for Flat Planel Display Manufacture"
Presented at Photon, Manchester, UK - September 2006
"Laser Direct Write of Active Thin Films on Glass for Industrial Flat Panel Display Manufacture"
Presented at LAMP 4th International Congress on Laser Advanced Materials Processing – May 2006
© 2006 Japan Laser Processing Society. This paper was published in proceedings for the above conference and is made available as an electronic reprint with permission of JLPS.
"Laser processing of polycrystalline diamond, tungsten carbide and a related composite material"
Published in the Journal of Laser Applications – May 2006
"Deep Engraving of Metals for the Automotive Sector using High Average Power Diode Pumped Solid State Lasers"
Presented at ICALEO – October 2005
"Cutting Flexible Printed Circuit Board with a 532nm Q-Switched Diode Pumped Solid State Laser"
Presented at ICALEO – October 2005
"Enhanced Cutting of Polycrystalline Diamond with a Q-Switched Diode Pumped Solid State Laser"
Presented at ICALEO – October 2005
"High Speed Cutting of Copper Foil with a 532nm Diode Pumped Solid State Laser for Microelectronics Applications"
Presented at the Third International WLT Conference on Lasers in Manufacturing, Munich – June 2005
"High Speed Processing Applications of High Average Power Diode Pumped Solid State Lasers"
Presented at the Third International WLT Conference on Lasers in Manufacturing, Munich – June 2005
"Laser Processing of Diamond, Tungsten Carbide and Related Hard Materials"
Presented at ICALEO and article in JLA – October 2004
"Laser Milling – A Practical Industrial Solution for Machining a Wide Variety of Materials"
Presented at LPM, Japan – May 2004
"Laser Milling of Metallic and Non-Metallic Substrates in the Nanosecond Regime with Q-Switched Diode Pumped Solid State Lasers"
Presented at HPLA, Taos, USA – April 2004
"A high-power short-pulse laser for EUV source generation using laser produced plasma and achieving low cost of ownership"
Presented at High Power Laser Ablation conference, Taos, USA – April 2004
"Emerging Applications for Q-Switched DPSS Lasers"
Presented at AILU – March 2004
"High Power Short Pulse Laser Modules for Laser Produced Plasma EUV Source"
Presented at Microlithography Conference, Santa Clara, USA – February 2004
"Emerging Applications Enabled by High Power nanosecond Pulse Diode Pumped Solid State Lasers"
Presented at ICALEO – October 2003